Greenworks 80V 24'' Dual Stage Snow Thrower, (3) 4.0Ah Batteries and Dual Port Charger Included

You must install at least 1 battery for operation. For best performance, it is recommended to utilize all included batteries.

This unit can be used effectively on gravel surfaces; however, it is necessary to raise the height of the skid shoes to avoid accidental injury or damage. Extreme caution should always be taken when using this product on an uneven surface.

In ideal conditions, our dual-stage snowthrowers can clear up to an 8-car driveway! It is important to note that the overall run time received is ultimately determined by the load acting against the unit and will fluctuate.

This unit has two hub motors, one for each wheel. Both motors are activated while moving straight, and one deactivates while turning.

Our 60V 24" Dual Stage Snow Thrower is currently sold as a tool only under model number 261702CTBT. The complete kit including 3x5.0Ah batteries and a dual-port charger goes by 2610702CT. While we do not currently have a tool-only 80V version available, we hope to have this available for you in the future!

Only Greenworks batteries, chargers, and machines of the same voltage are compatible and interchangeable with one another. Please be advised that the higher the ampere-hour (Ah) rating is on a battery, the more run time it can provide.

The batteries must be removed from the unit for charging and placed on a compatible Greenworks charger.

This unit is designed to be controlled manually to go upstairs, using the reverse function, or downstairs, in the forward position. Heading upstairs you will go up in reverse function while slightly pulling up and controlling the balance and weight. Going down the stairs we suggest going in reverse with the operator below, using the neutral or unit off position to roll the unit and control by the operator. Please note: Damage to wooden or composite stairs or decking may occur if not handled or controlled properly during this purpose. Always use extreme caution when maneuvering on stairs or unlevel surfaces.

Yes, this unit can be operated on slopes and/or hills. Always exercise extreme caution when operating on an incline and ensure you always have proper footing and balance.

Yes, please use designated snow thrower tire chains for this purpose. The chain must be designed for a 15" wheel (Tire specifications are AT 15 x 5-7). Please note that we do not currently manufacture or sell tire chains. Follow the instructions included with the chains to ensure proper installation.

Yes, they can be. Simply push the LED headlight button located above the power button to adjust the headlight function. There are 4 different light settings.

To move the chute, you must pull on the chute control handle. This will release the lock on the chute control gear and allow you to move the handle left or right. Once the chute has been directed, release the grip handle to lock the chute in the desired direction.

The drift cutters are located on each side of the unit. Simply loosen the knobs and pull the drift cutter until it has been fully extended. Repeat on opposite side. Drift cutters are designed to break down drifts during use and prevent snow from falling on the top of the housing; the drift will instead be knocked down in front of the auger to be removed.

Heavy or icy snow may cause the discharge chute to become clogged while in use. If you do get a clog, DO NOT attempt to unclog it with your hands or feet. Instead, turn your machine off and wait at least 10 seconds for it to fully stop. Then, use the supplied 3-in-1 snow brush to clear the clog. Operating Tip: If you notice that the chute is clogging often, try adjusting the angle of the chute and increasing the impeller speed.

The benefit of having an adjustable impeller speed ensures that the unit can be used in a variety of conditions. A lower auger speed usually translates to a smaller throwing distance - low speed also gives the user more control so that you can direct the snow where you want and avoid overshooting or re-covering previously cleared areas. When operating the unit at a higher speed, you can throw the snow further when the space allows and clear the area more quickly.

The battery chargers do have auto cut offs to prevent it from over charging. However, we do advise customers to remove the battery from the charger after it has been fully charged and to also unplug the charger from the outlet, as this is good electrical safety practice to do so. This will also help to prevent false defect readings and allows the charger to reset itself each time it’s used to charge a battery.

The battery is the most important component for a battery-operated unit. Please be assured we price our batteries with the cost of material, manufacturing, and current market pricing in mind. Batteries are the costliest items to manufacture and ship in any kit. Full kits including a tool, battery, and charger are priced affordably so that consumers can begin building that line of tools and move forward purchasing tool-only units. When you purchase batteries on their own, it is more notable the cost that they carry.

When the battery is not in use, we suggest storing it indoors, in a cool dry area - away from direct sunlight. Leave the charger unplugged and the battery disconnected from the charger unless it needs charging. It is recommended to store the battery with a full charge, and if it is being stored for a period where no use is expected, to check on the charge every couple of months. If you notice the charge has dropped, we advise charging the battery back up to full before returning it to its safe storage place. Following these steps will ensure you receive the most out of the battery life.

60V/ 80V Products: To remove the battery, push and hold the battery release button. Then, pull the battery pack straight out. In some cases, if the springs underneath have gotten locked down you might have to give a small push to the top of the battery to re-engage them to help the battery pop up. The battery pack fits snugly into the product to prevent accidental dislodging while in use; it may require a strong pull to remove. Before use, be sure that the rails on the battery and product are free of debris that could cause the battery to get stuck. 24V/ 40V Products: To remove the battery, press the latch button on the battery pack down and hold. Pull the battery pack out of the handle. The battery pack fits snugly into the product to prevent accidental dislodging while in use; it may require a strong pull to remove. Before use, be sure that the rails on the battery and product are free of debris that could cause the battery to get stuck.

Press the battery capacity indicator (BCI) button located at the end of the battery. The lights will illuminate according to the battery capacity level. Please note this switch does require a firm direct push using the tip of your finger. If the button is not being fully engaged, the lights will not activate. Please also be advised the lights only stay on for a few seconds and will automatically turn off. Another reason the lights will not power on is if the battery is completely depleted of power and needs to be charged.

Our batteries are interchangeable with tools that are of the same voltage platform only. The difference between batteries of the same voltage is the ampere-hour (Ah) rating. The higher the ampere-hour (Ah) rating on the battery is the more run time it has to offer.

There are a few exceptions. • Our 80V 20” snow thrower models 2600402 / 2605202 / 2601302 manufactured prior to September of 2017 can only use 2.0Ah or 2.5Ah battery models. • Our 60V 8.0Ah battery model 2957102 cannot be used in the following tools due to the height: dual-port lawnmowers, pressure washers, or the wet/dry vacuum.

Yes, they do. Each product line has designated charger models that can charge all batteries in that voltage platform, no matter the Ah rating.

The temperature of the battery prior to use should not be too warm or too cold. For snow throwers if the battery is too cold it may not be operatable. Allow the battery to get to room temperature prior to use. For our other tools allow the battery to cool down prior to use if it’s too warm. To avoid battery temperature issues, batteries should be stored indoors in a dry and cool location. Information on battery storage and temperature will in inside your owner’s manual.

Putting a battery that was just in use onto the charger often results in a false full charge signal. Remove the battery from the charger and allow it to rest in a room temperature area for approximately 10-15 minutes before charging.

When the battery is inserted into the charger and the status LED blinks red, remove the battery from the charger for 1 minute, then reinsert. If the status LED blinks green, then the battery is properly charging. If the status LED is still blinking red, remove the battery and unplug the charger for 1 minute. After 1 minute, plug in the charger and reinsert the battery. If the status LED blinks green, then the battery is properly charging. If the status LED is still blinking red, then this likely indicates an issue with the battery or charger and should be taken care of either with our warranty team or by means of replacement.

This typically indicates that the battery is at the wrong temperature to be charged. Allow the battery and charger to rest indoors at room temperature until they are no longer hot/cold and attempt charging again.

Greenworks chargers sold in the USA and Canada are designed for use on 120V outlets only.